Centurion D10, D20 Smart Installation Guide and Centurion D10, D20 Smart Installation Manual

Installation Guide D10 Smart

Preparation:

1. Gather all the required tools and equipment as listed on page 12 of the manual. This includes a ratchet and socket set, crimping tool, masonry drill bits, angle grinder, pin punch, hacksaw, spirit level, measuring tape, pliers, and safety equipment among others.
2. Check that no pipes or electrical cables are in the way of the intended installation.
3. Check that enough space is available for the gate operator, specifically for the release handle, and removal of the Gearbox Trim.
4. Check for loose, sandy soil if installing a foundation, as the soil condition may require a larger foundation.
5. Never fit the operator on the outside of the gate, where the public has access to it.
6. Install the gate operator only if it will not pose a hazard to the public, there is sufficient clearance to a roadway and/or public thoroughfares, the installation meets all municipal and/or local authority requirements once completed, the gate mass and application are within the operator specifications, and the gate is in good working order.

Conduit and Cable Length:

1. Route the cables as determined in the “Cabling Requirements” section.
2. Ensure that the conduits protrude above the concrete foundation.
3. The mains cables should protrude 450mm above the concrete foundation.
4. All signal cables should protrude 600mm above the concrete foundation.

Preparing the Operator for Installation:

1. Open the Camlock Cover.
2. Insert the Operator Key into the Camlock.
3. Unlock it by turning the key anti-clockwise.
4. Remove the cover of the D10 SMART / D10 Turbo SMART / D20 SMART to expose the internal components.
5. Place the cover to one side in a safe location.

Fitting the Batteries:

1. Gently push the left tab behind the Control Card backwards. This will allow the entire upper assembly to hinge forward.
2. Place a Battery into the designated area found on top of the Gearbox Trim on the left.
3. Route the Signal Wires below the Left Battery.
4. Route the Power Cables behind the motor and under the Right Battery.
5. Place the remaining Battery in its designated area on the right.
6. Connect both batteries up with the supplied harness.
7. Ensure that the harness is connected to the left side of the Charger.
8. Swing the upper assembly back into position over the batteries. A click should be heard if this is done correctly.

Accessory Installation and Storage:

1. There are dedicated trays below the D10 SMART / D10 Turbo SMART / D20 SMART Control Card to install and store any accessories connected to the Operator.
2. Wire the accessory device to the Operator.
3. Place the accessory device into the space provided.
4. Close the door.

Commissioning the System:

1. Download and install the “MyCentsys Pro” application onto your smartphone.
2. From the list of operators in the app, select the operator that is applicable to this installation.
3. Connect to the relevant operator using the app.
4. Follow the prompts in the app to configure the D10 SMART / D10 Turbo SMART / D20 SMART.

Applying the Warning Decal:

1. Apply the supplied warning decals to the gate as indicated on the reverse side of the decal.

Completing the Installation:

• Once all the necessary accessories and harnesses have been connected, ensure that the Camlock is in the “unlocked” position, and place the D10 SMART / D10 Turbo SMART / D20 SMART cover onto the gearbox.
• Once the cover is secured in place, lock the Camlock to lock the cover in place.

Installation Manual Centurion D10 SMART Gate Motor

D10 Smart Installation Manual PDF

Still, Struggling with your gate motor installation after following these instructions? Contact Pro Gate Motor today and get help today from a trusted partner in your area!

D10 SMART Installation Video Guide: Start to Finish

Still, Struggling with your gate motor installation after following these instructions? Contact Pro Gate Motor today and get help today from a trusted partner in your area!

Related Centurion Gate Motor Technical Info and Support Pages: