ET 300 Gate Motor Troubleshooting Guide
Displayed On Screen | Definition | Solution |
rdy | Unit is standing by and ready for next instruction | Trigger to run a required routine |
ac | Charger powered down due to Vac mains interruption | Check 220VAC or 29Vac supply to the unit. Check 500mA fast blow fuse in the 220Vac connector |
Bat | Battery is either disconnected or discharged | Check the 10A fuse in the battery lead. Allow 8-10 hours uninterrupted charge before trying to operate the unit again. If the battery has not recovered after this, then replace the battery |
rel | Gearbox manual release is in released (Manual) position | Lower the release lever to engage gearbox. Test manual release lever reed switch. Check that the manual release lever magnet has not been dislodged |
irb | Infra-red beams circuit is being triggered | Remove obstruction from the path of the safety beams. Check that beams are powered and functioning properly. Ensure the safety beam circuit end of line resistor has been installed properly as per this manual |
Hol | Control card is in Holiday Lock-out mode | Follow the steps on page 42 to deactivate Holiday Lock-out |
par | Control card is in Party mode | Follow the steps on page 43 to deactivate Party mode |
col | Multiple collision lock-out active | See page 32 and “Selecting a safety level” on page 20 |
for | Safety overload triggered by physical overload | See page 32 and “Selecting a safety level” on page 20 |
ref | Referencing the gate closed position | See “Referencing the closed position” on page 10 |
e-l | Failure to see the closed limit | See Installing the limit actuator on page 16 |
opn | Gate is open | Trigger gate to close |
pr9 | Control card is in Programming mode | Press and release X to exit programming mode |
e1 | Revolution counter/encoder failure | Ensure control card is fastened down correctly and that the ring magnet is installed correctly in place atop the motor shaft |
e3 | Motor is disconnected, motor fuse is fused or electric motor is faulty | Ensure the motor is connected correctly. Test the 10A motor fuse. Test the electric motor by disconnecting it from the control card and running it on a battery directly |
abt | Procedure aborted via the “X” button | Begin the procedure again |
dne | Procedure completed | Continue on to another programming option or exit programming |
e-l | Closed limit not installed correctly | See Installing the limit actuator on page 16 |
for | While buzzer beeps 20 times. Excessive gate resistance | Repair gate rolling load, so that it remains below the rated load specified on page 4 |
ful | Receiver memory is full | Delete any user addresses no longer in use |
to | Time out error while programming a remote | Begin transmitting with the remote before pressing set. Remote may be damaged or faulty. Ensure the remote does indeed transmit |
dec | Decoding error. The remote does not use a format that is compatible with the receiver |
Still, struggling with your gate motor installation after following these instructions? Contact Pro Gate Motor today and get help today from a trusted partner in your area!
ET 300 Gate Motor Troubleshooting Videos
ET 300 Gate Motor Troubleshooting Manual PDF
Below you will find a link to the Troubleshooting Manual that can be found on pages 49, 50 and 51 of the Installation Manual
ET 300 Installation Manual with Troubleshooting Guide PDF
Still, struggling with your gate motor installation after following these instructions? Contact Pro Gate Motor today and get help today from a trusted partner in your area!
Related ET Nice Gate Motor Installation, Programming And Troubleshooting Pages:
-
ET 300 Gate Motor Installation Guide with Installation Manual PDF
-
ET 300 Gate Motor Troubleshooting Guide and Troubleshooting Manual PDF
-
ET 500 Gate Motor Installation Guide with Installation Manual PDF
-
ET 500 Gate Motor Troubleshooting Guide and Troubleshooting Manual PDF
-
ET Gate Motor Status LED Indicator Guide for ET 300 and ET 500 Sliding Gate Motor
-
ET Nice Sliding Gate Motor Installation Manuals
-
How to Program ET Nice Gate Motor Remotes